Xenopixel Lightsaber: What It Is, Versions, Limits and What to Check

A Xenopixel lightsaber is a saber with a pixel blade that is run by a ready-made Xeno control board. The vendor listings we read name Xeno3.0 as the board in current Xenopixel sabers [1]. You get a Bluetooth app, preset sound fonts and effects. The trade is that the board is closed, so updates, fixes and support depend on whoever sells the saber.

This page explains the board. For a head to head with Proffie, GHv4 and CFX, read Xenopixel vs neopixel. For how every board family works, see the soundboards guide.

What Xenopixel is

Xenopixel is a commercial name for a family of low cost control boards sold inside mass market sabers. A board is the electronics in the hilt: it reads the motion sensor, plays sound through the speaker and tells the blade what to show [2]. The word describes the board and the sabers sold around it, so we write it as a technology name. It is not an official product of any film studio and has no connection to one.

Ultrasabers states that its Xenopixel sabers run on the Xeno3.0 board, and that its baselit models use a different board called XRGB3.0 [1]. A pixel blade, often called neopixel, is a tube with a strip of individually addressable LEDs inside. If that term is new, read what a neopixel lightsaber is first. The short version: neopixel is the blade, Xeno is the board that drives it.

Who designs the boards is not stated on the vendor pages we read. One vendor article credits a company called Nexus Sabers with announcing Xeno4 [3]. We could not confirm from an independent source who makes Xeno3, so we do not name a maker (unverified).

Xeno versions as documented

The Xeno4 article is written by a shop that plans to sell it, so treat it as marketing, not a test. It describes a staged rollout: the shop tests it first, then opens orders for selected sabers as a public beta [3]. We found no price in it. If a listing says Xeno4, ask the seller what stage of release it is.

What a Xeno saber can do

These features come from the vendor pages and guides we read, not from our own testing.

• Phone app. Ultrasabers says to download its XenoConfigurator app and connect the saber over Bluetooth [1]. Settings such as colour and font are changed there.
• Preset sound fonts. A sound font is a bundle of sounds for hum, ignition, swing and clash. Ultrasabers lists 16 or 34 preconfigured fonts [1]. Our sound fonts guide explains what is inside one.
• Preset effects. Padawan Outpost lists distinct ignition and blade effects and gesture control for Xenopixel [4]. The Saber Factory lists 12 blade modes and 8 effects for its Xeno3 neopixel [5].
• Pixel blade animations. Ultrasabers notes that tip drag and ignition animations need a Xenopixel blade [1]. The Saber Factory adds that some Xeno3 functions do not work with baselit blades, which were designed for neopixel [3].
• SD card storage. The Saber Factory describes Xeno3 as using a removable SD card, which it calls a common failure point in saber electronics [3]. Our soundboards guide covers why card quality matters.
• Charging. Charging details depend on the hilt. Read how to charge a lightsaber before the first charge, and use the cable that came with your saber.

Limits to know about

1. Closed board. Unlike ProffieOS, which is open source with public code [6], Xeno firmware is not something you can read or rewrite. You change what the app allows.
2. Firmware updates. We did not find a public update schedule or changelog for Xeno3 on the vendor pages we read (unverified). Ask the seller how updates are delivered and whether they are free.
3. Support depends on the seller. The warranty and the help you get come from the shop, not from an open community. Ultrasabers says its Xeno sabers are covered by its warranty but does not give the length on the page we read [1].
4. Bluetooth range through metal. The Saber Factory says aluminium hilts can shield Bluetooth and make app connections hard in many replica sabers [3].
5. Pixel blade durability. The blade sets durability, not the board. The Saber Factory rates a Xeno3 neopixel blade’s dueling durability “Medium” and baselit “High” [5]. For contact, see baselit vs neopixel.
6. Battery life. The Saber Factory lists 30 to 90 minutes per charge for its Xeno3 neopixel with a 3600 mAh battery [5]. Read the battery guide for lithium ion handling.

Typical prices for sabers with Xeno

The board is rarely sold alone, so prices are for finished sabers. Only prices we saw on a vendor page during this session are dated.

• Ultrasabers lists 12 premade Xeno sabers, from $320.00 to $355.00, as of November 2026 [1].
• SabersPro lists a Hunter with Xenopixel V3 at $180 (unverified, page not reachable when re-checked).
• CCSabers lists the SEA-8 at $325 with Xenopixel (unverified, same reason).

So a rough band is $180 to $355, with the lower figures unconfirmed. Hilts with only a baselit RGB board, which is the cheaper sibling, are covered in our best lightsabers under $100 guide. Prices change often, so check the live listing.

How to tell if a saber has Xeno

1. Read the listing. Sellers usually write Xenopixel, Xeno3, Xeno3Pixel or XRGB3.0 in the name or spec list [1].
2. Look for the app. A saber that pairs with the XenoConfigurator app is running a Xeno board [1].
3. Check the font count. Ultrasabers lists 16 or 34 fonts for its Xeno sabers [1]. A listing with a different count may use another board.
4. Ask the seller. Ask which board and which version ships, and in writing. The same hilt is often sold with two or three boards at different prices [2].
5. Do not rely on blade type. A neopixel blade can run Xeno, Proffie, GHv4 or CFX [2]. The blade does not tell you the board.

What to check before buying

• Which board and version ships, and whether it is Xeno3 or something sold as a “new” Xeno4.
• Whether the blade is pixel or baselit, since some functions need a pixel blade [1][3].
• The warranty length and who handles repairs.
• Whether the seller offers a replacement SD card and a way to reload fonts.
• Battery size, charging method and charger included.
• Whether the hilt is metal, if you plan to use the app a lot.
• Return policy, since we cannot vouch for quality.

Examples of Xeno sabers we found while researching: SabersPro Hunter, Xenopixel V3 (about $180, unverified) and CCSabers SEA-8, Xenopixel (about $325, unverified). Listing them is not a recommendation, because we have not tested either.

Upgrade paths to Proffie

If a Xeno saber feels limiting, there are two routes. The first is a chassis or board swap, which depends entirely on the hilt, so ask the maker before you buy or open anything. NovaSaber says its Xenopixel owners can move to its own SN-Pixel V4 Pro core [7]. The second is to buy a Proffie version of a hilt that is sold with both, as CCSabers lists for the SEA-8 at $395 (unverified) [8]. Read the soundboards guide for what Proffieboard adds and what it costs, and see turn off lightsaber sound for the documented mute steps on Xeno, which differ from Proffie. Sound problems on a Xeno saber are usually mute before they are hardware [9], and our troubleshooting guide lists the checks.

Sources

1. Ultrasabers, premade Xenopixel sabers and FAQ, https://ultrasabers.com/product-category/premade-xenopixel-sabers/ (accessed 2026-11-09)
2. Handbook, saber generations, handbook/sabers/generations.md (resting on Ultrasabers, The Saber Factory and NovaSaber)
3. The Saber Factory, Xeno4 announcement (vendor marketing), https://www.thesaberfactory.com/blogs/lightsaber-knowledge/xeno4-is-coming-to-the-lightsaber-world (accessed 2026-11-09)
4. Padawan Outpost, Proffie vs Xenopixel, https://padawanoutpost.com/blogs/outpost-archive/proffie-vs-xenopixel (accessed 2026-11-06)
5. The Saber Factory, saber tech comparison, https://www.thesaberfactory.com/pages/saber-tech-comparison (accessed 2026-11-06)
6. ProffieOS releases, https://github.com/profezzorn/ProffieOS/releases (accessed 2026-11-06)
7. NovaSaber, neopixel lightsaber technology, https://novasaber.com/pages/neopixel-lightsaber-technology (via handbook/sabers/generations.md)
8. CCSabers, SEA-8 listing, https://www.ccsabers.com/products/sea-8-rgb-neopixel-saber (unverified, not reachable on re-check)
9. Ultrasabers volume steps and AusSabers Xeno3Pixel guide, as summarised in our turn off lightsaber sound guide (sources listed there)